Here is the mistake most people make with a new shortwave radio: they find the SSB button, tune across the amateur bands in AM mode, hear quacking that sounds like a cartoon duck, and decide the radio is faulty. It is not. Single sideband (SSB) is a different way of sending voice, and your radio has to rebuild part of the signal before speech makes sense. Switch to the right sideband, tune slowly with the fine control, and the duck turns into a person.
This guide explains what SSB is in plain terms, why it sounds strange until it is tuned exactly, the USB and LSB rule of thumb, a step-by-step tuning routine, and what is worth listening for once you have the knack.
What single sideband actually removes
An ordinary AM signal has three parts: a steady carrier in the middle and two mirror-image copies of the audio on either side, called sidebands. The carrier carries no speech and both sidebands carry the same speech, so two-thirds of the package is, in a sense, spare.
SSB throws the spare parts away. The transmitter suppresses the carrier and filters off one sideband, sending only the upper sideband (USB) or the lower sideband (LSB). As the Wikipedia article on single-sideband modulation puts it, this avoids the doubled bandwidth of AM and the power wasted on a carrier, at the cost of more complex equipment and more difficult tuning at the receiver.
| AM | SSB | |
|---|---|---|
| Carrier sent? | Yes | No (suppressed) |
| Sidebands sent | Both | One |
| Space on the band | About twice the audio width | About the audio width |
| Ease of tuning | Easy, sounds right across a wide spread | Needs fine, careful tuning |
That efficiency is why SSB became the workhorse for long-distance voice. The same article notes that the US Strategic Air Command adopted it for its aircraft in 1957 and that it became a de facto standard for long-distance voice radio after that. New to the idea of carriers and sidebands? Start with our walk-through of amplitude and frequency modulation, then come back.
Why it sounds like a duck until you tune it
Because the carrier is missing, your radio has to supply its own. It does that with a beat frequency oscillator (BFO) and a product detector, which together shift the sideband back down to normal audio. The catch is precision. The Wikipedia article says that if the BFO is off by more than about 30 Hz, speech is shifted up or down and sounds “Donald Duck”-like, and it gives a tuning tolerance of roughly plus or minus 125 Hz for voice.
On a dial where broadcast AM stations are 5 or 10 kHz apart, 30 Hz is a tiny nudge. That is the whole secret: SSB needs a fine tuning step that an ordinary AM radio does not have.
Quick check: does your radio do SSB?
- Look for a mode button marked SSB, USB/LSB or BFO.
- Look for a fine tune knob or a tuning step you can set to 10 Hz, 20 Hz or 50 Hz.
- If the radio only has AM and FM, it cannot resolve SSB properly, whatever you do with the dial.
The USB and LSB rule of thumb
When you hear SSB voices on the amateur bands, the convention described in the Wikipedia article is simple:
- Below 10 MHz, amateurs normally use LSB. On the 40 metre band, for example, voice contacts often sit around 7.100 MHz in lower sideband.
- At 10 MHz and above, they normally use USB. On the 20 metre band around 14.200 MHz you would select upper sideband.
- The exception: the five amateur channels near 5.3 MHz (60 metres), where US rules require USB.
Outside the amateur bands, do not assume. If a signal will not resolve in one sideband however carefully you tune, switch to the other and try again.
Tuning SSB step by step
- Pick a busy band at the right time. 40 metres in the evening and 20 metres in daylight are good starting points. Our guide to why signals travel differently at night explains why the time matters.
- Select the sideband using the rule above.
- Set a coarse step (1 kHz) and tune until you hear voice-like burbling.
- Switch to a fine step (10 to 50 Hz) or use the fine tune knob.
- Turn slowly. Too far one way, the voice sounds deep and robotic; too far the other, it sounds like someone who has breathed helium. Keep turning in the direction that makes it more natural.
- Stop when it sounds like a normal voice. Male and female voices both have a natural pitch you will recognise once you are close.
- Narrow the filter if the radio allows. A filter around 2.4 to 3 kHz wide suits SSB voice and cuts the hiss from either side.
Common tuning problems
| What you hear | What is wrong | Fix |
|---|---|---|
| Garbled speech that never clears | Wrong sideband | Switch USB/LSB and retune |
| Voice clear for a minute, then drifts | Receiver warming up, or the other station drifting | Give the radio ten minutes to settle; retune |
| Loud thumping or splatter | Very strong nearby signal | Use the attenuator or reduce RF gain |
| Voice fine but buried in hiss | Weak signal or noisy location | Better antenna, narrower filter, move away from electronics |
What you can hear once SSB clicks
- Amateur radio conversations from across your country and, when conditions are good, other continents. Our introduction to shortwave listening today covers the bands and the gear.
- Long-distance utility voice on HF, the kind of traffic SSB was adopted for.
- Morse code and digital modes, which also need the BFO to be audible as tones.
Be aware that in some countries, the UK among them, listening to messages not intended for the general public is restricted. Broadcast and amateur signals are the safe ground for a new listener.
Making SSB easier on the ears
SSB voice is deliberately narrow. Standard SSB is about 2.9 kHz wide, and the classic speech channel the Wikipedia article describes runs from roughly 300 Hz to 3,400 Hz. That is why it sounds thin compared with broadcast audio. If you record it, an equaliser with a high-pass and a low-pass filter will trim rumble and hiss outside that range; this practical overview of using equalisers shows how the filter types work.
On the radio itself, small habits help: use headphones, keep the volume moderate, and turn down RF gain on strong signals rather than turning the volume up on weak ones.
Frequently Asked Questions
Can I hear SSB on a radio without an SSB button?
Not properly. An AM-only receiver has no oscillator to replace the missing carrier, so SSB stays as quacking. Some listeners place a second radio nearby so its internal oscillator acts as a crude BFO, but the results are unreliable. If you want to hear SSB, buy a receiver that lists SSB, USB and LSB in its specifications.
Why do amateurs use LSB on lower bands and USB on higher ones?
It is a long-standing convention rather than a law of physics, and following it means everyone on a band uses the same sideband and can hear each other. The main exception is the 60 metre band channels near 5.3 MHz, where US rules require USB. For a listener, the practical point is simply to know which mode to select.
Do shortwave broadcast stations use SSB?
The big international broadcasters mostly use ordinary AM so that any shortwave radio can receive them. SSB is mainly heard from amateurs and professional two-way services. That is why a radio without SSB is fine for broadcast listening, while hobbyists who want to explore the bands between the broadcast stations usually look for SSB first.